Hydraulic rotating arm, no motor
A 650 mm arm turns on water reaction force alone. Fewer parts in the grease stream means nothing to seize, jam or replace — the usual failure points of a motorised wash system simply are not there.

Self-Cleaning ESP · KL-D-Q60 / Q80 / Q160 / Q200 / Q240 / Q320
A stainless electrostatic precipitator that washes its own cell with a 650 mm hydraulic rotating spray arm, on a schedule you set. 98% purification, no dismantling, no operator — and maintenance labour down by more than 80% against a manual ESP.
Overview
Every manual ESP has the same failure mode: the cell gets washed less often than it should. Grease builds on the collecting plates, efficiency slides, the discharge starts to show, and nobody notices until a spot check. The KL-D-Q is built around removing that judgement call. A spray arm inside the cabinet washes the cell on a cycle you set between one and fifteen days, runs overnight after service, and drains the wash water through an oil-water separator.
The arm is driven by the reaction force of the water itself — no motor, no gearbox, no bearings in the grease stream. It turns at constant speed as soon as water flows, sweeping both faces of every plate with 650 mm of reach through Φ2.2 mm anti-clog nozzles. Because nothing has to be dismantled, the cell is never dropped, never distorted and never refitted at the wrong spacing.
The full cycle runs unattended: shutdown and static discharge, water inlet, detergent dosing, 360° wash, waste discharge, fan drying, reset. Water, detergent dosing and drainage are handled by the external washing main unit supplied with every cabinet.
Need the full datasheet with drawings and test references? Ask and we will send it with the quotation.
Engineering
What matters more on a real installation than on a specification sheet.
A 650 mm arm turns on water reaction force alone. Fewer parts in the grease stream means nothing to seize, jam or replace — the usual failure points of a motorised wash system simply are not there.
Set the interval from 1 to 15 days and let it run after closing, or start a deep clean from the 7-inch touch panel when the kitchen has had an unusual week. Both modes use the same cycle.
A sloped sump gathers the oily wash water after each cycle and a DN50 port takes it away in a fixed direction. Daily upkeep becomes looking into the collection area occasionally, not scraping plates.
Because the cell is washed on schedule instead of on memory, purification stays at 98% and odour removal above 60%, meeting GB 18483-2001 and suitable for low-level discharge.
The sixth-generation closed-loop supply trips within 0.05 s on short circuit, leakage or arcing, and releases stored charge at shutdown so an inspection does not put anyone near a live cell.
Shell, chamber, duct and spray piping are stainless, one-piece bent and fully welded. The screen, cell and spray arm each come out independently through the front, so a service does not need the cabinet moved.
Specifications
| Model | Airflow (m³/h) | ESP cells | Dimensions L×W×H (mm) | Flange W×H (mm) | Cabinet |
|---|---|---|---|---|---|
| KL-D-Q60 | 6,000 | 2 | 970 × 870 × 850 | 520 × 750 | Single |
| KL-D-Q80 | 8,000 | 2 | 970 × 870 × 850 | 720 × 750 | Single |
| KL-D-Q160 | 16,000 | 4 | 1580 × 970 × 850 | 1330 × 600 | Single |
| KL-D-Q200 | 20,000 | 4 | 1020 × 970 × 1700 | 870 × 1600 | Double stack |
| KL-D-Q240 | 24,000 | 8 | 1170 × 970 × 1700 | 930 × 1450 | Double stack |
| KL-D-Q320 | 32,000 | 8 | 1580 × 970 × 1700 | 1330 × 1450 | Double stack |
Every unit is supplied with an external washing main unit (980 × 990 × 850 mm) containing the wash pump, water tank and controls. General: ≥98% purification, ≥60% odour removal, IP65, 7-inch touch panel, optional IoT module, DN50 drain, 220 V / 50 Hz. A mains water inlet and a drain are required on site. Dimensions are from the CAD drawings; non-standard sizes can be built.
Applications
The recommended model is the configuration we would quote for a standard layout; longer, split or stacked runs are quoted on drawing.
Many tenants on one exhaust riser with a wildly fluctuating fume load. Washes at night by trading schedule so no tenant kitchen closes for cleaning.
Recommended: KL-D-Q320
Concentrated wok bursts at lunch, high fume concentration, and a facilities team with no time for a wash rota.
Recommended: KL-D-Q160 / Q200
Unattended operation with no dedicated maintenance staff, and an audit trail for environmental inspection.
Recommended: KL-D-Q200 / Q240
Continuous production shifts where stopping the exhaust to wash a cell is not an option.
Recommended: KL-D-Q240 / Q320
Very heavy grease load where a manual cell would need washing every fortnight and would still foul early.
Recommended: KL-D-Q160
An existing riser that keeps failing inspection because the old unit is never cleaned on time.
Recommended: KL-D-Q80 / Q160
FAQ
A spray arm inside the cabinet rotates over the ESP cell and washes both faces of every plate with water and detergent. The arm turns on the reaction force of the water, so there is no motor in the grease stream. The cycle runs on a timer — typically overnight — then drains through an oil-water separator, dries the cell with the fan and resets.
Yes. A mains water inlet and a drain are both required, plus the external washing main unit that ships with the cabinet. If site water is awkward, the Smart Water Tank stores and recirculates the wash water instead of plumbing the unit directly.
A cycle takes around ten minutes of spray. The tank in the washing main unit is refilled per cycle rather than running continuously, so consumption tracks the interval you set — a 15-day cycle on a lightly loaded kitchen uses very little.
The cell, no. The equalising pre-filter screen still wants a rinse periodically, and the grease collection area should be inspected. That is minutes a month rather than a crew and a shutdown.
The controller detects the water shortage, stops the cycle, alarms and protects the pump from running dry. Wash failure does not damage the cell; it just leaves it unwashed, and the alarm tells you.
Compare the cleaning cost, not the purchase price. A manual cell on a heavy-grease kitchen means a crew, a shutdown and a service fee every cycle, plus the efficiency decay between washes and the compliance risk that comes with it. On any site where the wash interval would realistically slip, the self-cleaning unit pays back inside two years.
Next step
Appliance list, hood length and the duct route are enough to come back with a model, an airflow figure and a drawing. OEM and ODM enquiries welcome.